If you have recorded a macro that is almost right, but you need to add a few commands to it, you can easily append the commands to an existing macro instead of recording the whole thing over again. See the discussion on vim_dev about unexpected behavior of the :let command for details. Possible workarounds include using the setreg() function or adding "no-op" commands to the end of the macro, such as a. The reason for this is to make registers set with :let act "the right way" when dealing with yanked/deleted text, but it can cause headaches when dealing with recorded macros. This is because, as documented in Vim will treat the register as "linewise" under these conditions. If :set viminfo? shows a value including (for example) or character (carriage return or newline). The ' viminfo' option can disable the saving of registers. On restarting Vim, you can press to run the macro from register a. For example, you might record a macro to register a, then exit from Vim with :q!. Simply by including the proper text in your 'viminfo' option or leaving the nocompatible default alone, Vim will automatically write all your registers to a file and restore them at startup.īy default, the content of each register is saved, and will be available next time you run Vim. The simplest way occurs by default if you run Vim in nocompatible mode (which is the default if you have a vimrc). There are two primary ways of saving a macro for later use. Typing :reg abx will show the contents of registers a, b, and x. For example, use :reg to view all registers, or :reg a to view only what you have recorded into register a. You can use the :registers command to view the current contents of any or all register values in Vim. Type :normal to run the macro from register q on each line.Visually select some lines (for example, type vip to select the current paragraph).You can run the macro on each line in a visual selection in a single operation: Suppose you have a macro which operates on the text in a single line. Play the recorded keystrokes by hitting space.End recording with q (first press Escape if you are in insert mode).:nnoremap Start recording keystrokes by typing qq. Use this mapping as a convenient way to play a macro recorded to register q: The 2 means that what follows is performed twice, and the plays back the last used macro. That should change the second line, with the cursor finishing on the third line. The cursor should now be on the second line. Type the following to move the cursor to the start of the line, then down to the next line:.Type the following to append " '," to the line:.Type the following to insert four spaces followed by " '" at the start of the line:. Type the following command to change the first sequence of whitespace to " ': '":.Type qd (the q starts recording the d is the register where keys will be recorded).The following shows one way to record a suitable macro. When finished, manually insert the initial " data = " line. Then, playback the macro to change each other line. To do this, record a macro while changing the first line. Suppose you want to change the data to make a dictionary for a Python program, with this result: To execute the macro times (once by default), the complete process looks like: With $ tail /etc/vim/vimrc.Each register is identified by a letter a to z. # know how to handle pipes, it fails with a `Permission denied` error.Īlso check that you have permission to globally read this file: sudo chmod 644 /etc/vim/vimrc.local # It's the same general idea, and simpler, but because sudo doesn't # $ sudo echo 'colorscheme default' > /etc/vim/vimrc.local You can easily do that in bash with this line: $ echo -e "\"Use default colors for vim:\ncolorscheme default" \ I think the best solution is to append your line to /etc/vim/vimrc.local like this: So you can append this line to either of these two files. To append that correctly, first look at your /etc/vim/vimrc file.Īt the bottom of mine, I see these lines which include /etc/vim/vimrc.local: " Source a global configuration file if available I would also put a comment above it like "Use default colors for vim".) (I suggest using the full, un-abbreviated term 'colorscheme', so that when you look at this years later you'll be able to more easily figure out what that darn thing does. (lol, how did that happen?)Īdd a line to your system vim setup file in /etc/vim/ that says colorscheme default So all of the other answers here, so far, get both of these wrong. The default colorscheme, "for all vim sessions", is not set simply by adding a line to your ~/.vimrc, as all of the other answers here say, nor is the default set without the word 'default' being there. 'for all vim sessions', not simply for the current user. The ' default', not some other color profile, and
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |