![]() On top of the controller there is a stunt button. By pressing left or right it will rotate the direction you are pushing. ![]() The toggle on the left is a throttle/rotation stick. The other 4 green buttons on the right side of the controller adjust the settings of the blades. ![]() The toggle on the right controls flying forwards, backwards, or sideways. Changing the number will either decrease or increase the sensitivity of the remote control to the drone. They recommend that you start at #1-beginner until you’ve gained some experience. This can be adjusted to your skill level. Just below that is a slider button with the numbers 1, 2, ad 3. In the center, at the top, there is a power button. While the battery was charging I familiarized myself with the remote control. When it is lit green that means it is fully charged! When it is lit red that means it is still charging. There is a light indicator on the side of the charger. It just plugged into the battery and the other end plugged into my computer. I had never seen a charger like this before, I am very glad that it came with it. Next I wanted a fully charge battery so I could spend some time playing with the drone! I followed the instructions and unscrewed the battery compartment and removed the LiPo rechargeable battery. Putting the blade protector’s on was our first step. The blade protectors are for when you are flying indoors. Skyrocket Toys have really planned ahead and sent every accessory needed for this video drone! In the box you will find, a RC video drone, remote controller, micro SD card adapter, micro SD card, rechargeable LiPo battery, USB charging cable, screws, 4 replacement blades, 4 blade protectors, and a screwdriver! I LOVE that they send the perfect sized screwdriver! This article also available below as a Word Doc.If you’ve been playing with the idea of getting a fun flying toy may I suggest the Sky Viper HD Video Drone from Skyrocket toys! A typical remote controlled helicopter has 2 blades, this awesome drone has 4 blades, which allows you to not only do stunts, but to also fly up, down, left, right and every direction in between! With a removable camera that can take photos or record footage this drone really takes it up to the next level of fun! Once back on the main menu, tap "Start" to begin viewing the video from your drone. Make sure your phone and drone are in close proximity as the phone needs a good connection to pass the firmware update to your drone.ġ4. If the firmware update fails, just force quit the app and then open it again. When they return to the normal flashing pattern, the drone is updated and the app will take you through the controller tutorial and then back to the main menu. The drone's LEDs will begin to flash rapidly during the firmware update. Note: You don't need data or internet connection for the firmware updateġ3. The app will prompt you for a firmware update. After you are fully connected to the "SKYVIPER17_xxxxxx" network again, return to the Sky Viper Video Viewer app.ġ2. Open the WiFi settings on your phone and connect to it again.ġ1. Your phone will then automatically disconnect from the "SKYVIPER17_xxxxxx" network. Enter your new password twice (must be exactly 8 characters)ġ0. Wait for the "create password" prompt to appear.Ĩ. Conect to the "SKYVIPER17_xxxxxx" WiFi network and ensure that your phone says it's connected (wait for all progress wheels etc. If there is a password on the network and you do not know what the password is, reset the password by holding down the L trim, R trim, and Power buttons for 5 seconds.ĥ. It is best to turn off the phone data as well Open the wifi settings on your phone and forget all previous networks. Turn on your drone and controller (place the drone on a flat surface)ģ. Turn off the Sky Viper Video Viewer app and ensure that it is not running in the backgroundĢ. The Wifi password is now erased, and you should be able to connect to the WiFi and set a new password in the app.ġ. Then hold down the "L" trim, "R" trim, and power button down simultaneously for 5 seconds (or until the controller beeps). To do this, first turn on the controller and drone. Try resetting your drone's WiFi password. I CAN'T CONNECT TO THE WIFI (FORGOT PASSWORD) If that still doesn't work, make sure the drone's battery is fully charged and that you have fresh AAA batteries in the controller.Ģ. Make sure the drone is on a level surface (and NOT moving). Turn the controller and drone off and back on again to see if they pair. The controller will beep once and then begin beeping continuously to indicate that it is searching for a drone. Hold down the F-trim, B-trim, and power button for 5 seconds. MY DRONE WILL NOT CONNECT WITH THE CONTROLLERĬontrollers are not cross compatible so ensure that are using the controller that came with your drone
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |